Feedback
For the last six years, I have answered many thousands of personal emails that you have sent to UK Free TV.
Sadly, I am unable to offer this personal service at the moment.
Until I can restore this service, please can you leave any questions you have on an appropriate page, where they will be answered as soon as possible, or below, if you can't figure out where to ask.
I look forward to your questions!
Help with TV/radio stations?
In this section
Sunday, 13 October 2013
M
Michael3:01 PM
r. bedford: Go to menu > channel > manual store, then input channel 55 (frequency 746MHz and 8MHz if required) if you want to manually tune in the BBC channels from Midhurst.
If it doesn't allow you to do that, go to menu > setup > plug and play to reset the TV.
link to this comment |
R
r. bedford3:15 PM
Horsham
Thanks. Tried that and nothing
link to this comment |
r.'s: mapR's Freeview map terrainR's terrain plot wavesR's frequency data R's Freeview Detailed Coverage
R
r. bedford3:25 PM
Horsham
Also if it helps the channel number on screen says 1Atv where normally it would say 1dtv and so on
link to this comment |
r.'s: mapR's Freeview map terrainR's terrain plot wavesR's frequency data R's Freeview Detailed Coverage
M
Michael3:32 PM
r. bedford: Then you'll need to press either the TV button, or source button then select DTV.
First rule before you do anything is check the TV is actually in digital mode and not try to display non-existent analogue channels!
link to this comment |
R
r. bedford3:37 PM
Horsham
I thought that might the case but when I press tv. Nothing happens and there is no dtv option
link to this comment |
r.'s: mapR's Freeview map terrainR's terrain plot wavesR's frequency data R's Freeview Detailed Coverage
M
Michael3:47 PM
r. bedford: Ok, then try pressing button 2 for channel 2, then once it goes to it, press button 2 again and it should switch back to DTV mode.
link to this comment |
R
r. bedford3:48 PM
Horsham
Tried that already!! Stays on atv!
link to this comment |
r.'s: mapR's Freeview map terrainR's terrain plot wavesR's frequency data R's Freeview Detailed Coverage
J
jb385:27 PM
r. bedford: Do you have the operating manual for your TV? because if not I will attempt to paste in the "plug and play" section as on having had a look through same, it is as was expected with any Samsung manual, horrendous!!
link to this comment |
R
r. bedford5:50 PM
Horsham
I found the apparent solutions on another site whereby I accessed the 'hidden' menu. It told me to do a factory reset which would bring back the dtv option. I did this but am still left with atv. It was also suggested pressing the tv button a few times to enable it to switch from analogue to digital but this does nothing either. This factory reset actually takes you through plug and play but when that finishes I'm left with the same problem
link to this comment |
r.'s: mapR's Freeview map terrainR's terrain plot wavesR's frequency data R's Freeview Detailed Coverage
J
jb386:08 PM
r. bedford: If you now have the manual stored? then when going through the "plug and play" menu the important section that determines whether DTV or analogue is scanned starts from paragraph 4.
4. Press the ENTER button then select the appropriate country by pressing the or button. Press the ENTER button to confirm your choice.
5. Press the or button to select Air or Cable, then press the ENTER button.
Air: Air antenna signal - Cable: Cable antenna signal.
6. Press the or button to select the channel source to memorize. (Digital or Analogue) Press the ENTER button to select Start.
link to this comment |
Select more comments
Your comment please