menuMENU    UK Free TV logo Archive (2002-)

 

 

Click to see updates

Feedback

Changes to feedback page

Changes to feedback page
published on UK Free TV

For the last six years, I have answered many thousands of personal emails that you have sent to UK Free TV.

Sadly, I am unable to offer this personal service at the moment.

Until I can restore this service, please can you leave any questions you have on an appropriate page, where they will be answered as soon as possible, or below, if you can't figure out where to ask.

I look forward to your questions!



Help with TV/radio stations?
BBC Three Linear channel re-opens1
Will car radios have to be replaced?2
Will UKTV History and FTN eventually be available on fSfS or Freesat? They are 3
Could u please explain why there are no subtitles on most of your films terresti4
Can I pay as you go for British Europsort on my digital tv without subscribing?5
In this section

Comments
Sunday, 30 September 2012
J
jb38
sentiment_very_satisfiedPlatinum

8:23 PM

matt hope: Thats is inclined to suggest the possibility that a strong Freeview signal is close (or on) the RF channel used by the Sky box, you should have a check to ensure that Sky's RF output channel used above 64 (pref 68/69) and if you have to change it then remember to retune the TV again (on analogue) to pick up the new channel.

link to this comment
jb38's 7,179 posts GB flag
Monday, 1 October 2012
J
jb38
sentiment_very_satisfiedPlatinum

6:55 AM

matt hope: Of course there is an easy way to verify whether or not the Freeview signal is responsible for the problem, and simply done by temporarily removing the normal aerials connection into the Sky box and checking the result of this action on the upstairs TV.

link to this comment
jb38's 7,179 posts GB flag
M
Mike Held
8:56 PM
Milton Keynes

Our Milton Keynes location is almost midway between the Sandy Heath and Oxford transmitters. When I have to retune my freeview box it is 50/50 which transmitter is detected. I often end up with just a few TV channels listed as '800', '801', etc. It often seems to take 5 or 6 retunings to pick-up the Sandy Heath channels. Is there a way I can block out the Oxford signal - perhaps by covering the south-west side of the aerial?

link to this comment
Mike Held's 1 post GB flag
Mike's: mapM's Freeview map terrainM's terrain plot wavesM's frequency data M's Freeview Detailed Coverage
J
jb38
sentiment_very_satisfiedPlatinum

9:18 PM

Mike Held: This might seem rather elementry, but I assume that your box does not have a manual tuning facility? as if it does then either reset the box or carry out a retune with the aerial disconnected as that will blank the memory out, then manually tune in Sandy's muxes one at a time, these being:
27 - 24 - 21(HD) - 51 - 52 - 48.

link to this comment
jb38's 7,179 posts GB flag
Tuesday, 2 October 2012
S
Stephen P
sentiment_satisfiedGold

12:32 PM

Mike H - Can you not switch the channels round so that the ones you want appear in 1/2/3/4/5 etc? Usually possible.

One trick is to unplug the aerial when the unwanted channels are bing scanned. Depends if the numbers are close or widely spread how achievable that is.

link to this comment
Stephen P's 1,173 posts GB flag
M
matt hope
5:58 PM
Burnley

matt hope:
jb38 the rf channell is set too 68 and still black and white upstairs
the tv is a grundig GU37BLKSE model any more help please.

link to this comment
matt hope's 3 posts GB flag
matt's: mapM's Freeview map terrainM's terrain plot wavesM's frequency data M's Freeview Detailed Coverage
J
jb38
sentiment_very_satisfiedPlatinum

9:37 PM

matt hope: If the picture on the Grundig looks perfectly OK apart from the fact that it's in black and white, then that suggests equipment failure rather than anything you have done, and with the problem being either with the Sky boxes modulator or alternatively (and more likely) with the colour decoding circuitry in the analogue side of the Grundig, this fault nearly always caused by crystal failure.

The only thing I can suggest is to try and borrow a small colour TV that is capable of analogue reception and then couple that into the link from the Sky boxes output, giving the borrowed TV an analogue scan to pick up the RF output channel from the Sky box for the purpose of checking the image obtained, black and white or colour, because if its colour then obviously the fault is with the Grundig.

By the way temporarily change the output on the Sky box from RF2 over to RF1 so as "not" to feed voltage into the borrowed TV's aerial socket.

Should you not be able to borrow a TV then if you have an old VHS tape machine around you could couple its RF output into the Grundig and retune same (TV) to pick up the VHS machines analogue signal, no tapes or aerial required as its only the modulator output you are interested in and with regards to whether anything seen is black and white or not.

link to this comment
jb38's 7,179 posts GB flag
Wednesday, 3 October 2012
M
Michael Frost
10:51 AM

Hi JB38. This will seem an extremely odd request but could I ask if you are the same JB38 that gives advice on 'Pechorin's' website? If you are I have tried to contact you for the instructions to bypass the dewpoint sensor on my JVC GR-DX97 camcorder. I'm not sure that I was submitting it correctly or that it was ever rec'd. If you aren't THAT JB38 please accept my apologies.

link to this comment
Michael Frost's 1 post GB flag
S
sally
11:10 AM

i want to know if the olevia 32ra108s is multi system,or ntsc thanku

link to this comment
sally's 1 post HK flag
D
dean
9:14 PM

Hi, not that technical but had and used AV systems for years so familiar with setups, signal strength, installations etc.

I have noticed a problem and have been searching an answer for ages. With more than one make/ model of freeview tv that seems to be data related, not signal strength. I always keep updated with regular wipes and installations for new channels. (except sadly they're mostly selling channels).
But after tv has been on for at least a 1/2hr, the channel selection becomes frozen and eventually flashes through all the 'switched' channels, catching up with the frantic button presses. Also the epg data is missing. Just says 'No information available'. The only thing that resolves the problem is to switch off the set, wait 30 seconds and then switch on with full epg and channel change working normally again. I also notice that when switching through channels, ones with 'Loading interactive services' also seem to take ages and are much like a website bogged down with java ads and cookies hogging the cpu. Is this the future of digital TV? It isn't just my sets that do it either.

I am on Guildford transmitter, (tried london) and receive london regional.

link to this comment
dean's 4 posts GB flag
Select more comments

Your comment please
Please post a question, answer or commentUK Free TV is here to help people. If you are rude or disrespectful all of your posts will be deleted and you will be banned.







Privacy policy: UK Free Privacy policy.