How do I change the RF output channel on a Sky Digibox?
Press the [SERVICES] button and then press [4] [0] [1] then [SELECT]
Then press [4] to go to the RF output menu.
You can now change the value so that it does not clash with an analogue TV channel or a Freeview multiplex.
HD and "new EPG" boxes
If you have a HD box, press [SERVICES] button and then press [0] [0] [1] then [SELECT]. Nothing is shown on the TV screen until you press the Select button.Then use the [RIGHT] arrow button on the remote until this screen is shown, and press SELECT to change the values:
All questions
In this section
Saturday, 26 March 2011
D
david8:44 PM
Thanks for your help LutonFan, much appreciated. I shall recommend this site to anyone I know who has trouble in the future.
link to this comment |
Wednesday, 30 March 2011
Brian Wright
8:52 AM
8:52 AM
Hi David,
Once you have tried the coax lead when plugged into RF 1 o/p to your known good set don't do anything except transfer it to the RF 2 o/p. If it does'nt work then the RF 2 o/p is faulty.This check test illiminates any retuning and its obviuos complications of addad unknowns at an early stage.
I hope this helps
Brian
link to this comment |
Wednesday, 13 April 2011
J
James12:30 PM
Hello,
I have a digisender that sends sky from our bedroom to the receiver in the kitchen. We also have another receiver in the kids bedroom. The picture is fine in the bedroom but the picture in the kitchen is blighted by interference. We have a loft aerial with a distributor and tv points in most rooms. I was wondering if I connected the RF out on the sky box to the tv point on the wall, would I be able to pick up the signal in the kitchen using the tv point there. Basically, even though there is a terestrial signal being sent to all the rooms, can I reverse feed a sky signal from the bedroom in to the splitter and from there watch the picture on the kitchen tv?
link to this comment |
Thursday, 14 April 2011
James: It should work, but the picture quality may not be acceptable.
link to this comment |
N
Neil King3:35 PM
Please could you help me?
I have SKy HD and use RF port on rear of my Sky HD connected to a splitter which is cable to my bedroom and kitchen so I can change Sky channels in these other rooms. Unfoirtunately my other half puled out the coax areal cable from the RF port and the pin from centre of the ariel port that power my RF Out has come out. I tried swapping my RF port out but seems like RF power supply is only avail via port 1?
Can I eeasily re solder a new replacement RF socket to my Sky HD board?
Regards
Neil King
link to this comment |
Friday, 15 April 2011
Neil King: I can be very hard to fix this kind of problem, and any such action will invalidate your warranty.
You are correct, only one port has the power output to drive the Magic Eye device.
link to this comment |
Thursday, 5 May 2011
J
Jim Hince10:22 AM
my magic eye will not work in my study. I can connect my TV in the study to the RF port without teh magic eye and it works ok but when I connect the magic eye it will not work. I am not getting a power light on the magic eye when connected to my study but if I put it on the cable behind the main TV it lights up ok
link to this comment |
Tuesday, 10 May 2011
L
lawrence7:07 PM
i haved moved house from the north east to gloster and i still get tyne tees news and bbc north east how can i change this
link to this comment |
Wednesday, 11 May 2011
lawrence: The services you get depend on the address registered with Sky, please phone them up and let them know you have moved.
link to this comment |
Thursday, 12 May 2011
K
Kenpblue10:12 PM
I have a Sky HD box in my lounge HDMI'd to the lounge TV. No problem. I have coax wired the RF 2 to my bedroom tv aeriel inout and can get SkyHD there too. I added a magic eye to the coax in-line upstairs turned the RF2 power on the Sky box on so I can use the Sky remote upstairs and all works fine. But I have now put my lounge HD Box in a vented but closed cupboard and so I put a magic eye in-line downstairs too. That lights up ok and works but it then stops the upstairs magic eye working. It seems I can only have one magic eye either up or down. Is the an easy solution?
link to this comment |
Select more comments
Your comment please